Contents
- Index
COM API - Control Functions
The following functions can be used to control the analzyer.
Function Groups
Analyzer Operations
Analyzer Configuration
Plot and Window Commands
Overlay Control
File Management
File Positioning
File Post Processing
Signal Generation
Digital Input and Output Lines
Analyzer Operations
Run()
Description: Run the analyzer or start recording
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
Stop()
Description: Stop the analyzer or recording
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
Record()
Description: Start recording
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
RecordPause()
Description: Pause the current recording. The analyzer will continue running but data will not be stored in the wave file.
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
RecordResume()
Description: Resume a paused recording.
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
FileStep( int numFFTSteps )
Description: Performs the specified number of FFTs starting at the current file position and advancing by the overlap setting (Post Processing mode only)
Parameters: numFFTSteps: 1 or more
Return: S_OK = success, E_FAIL = unsuccessful
Trigger()
Description: Forces a single trigger event. Analyzer must be running and triggering must be enabled.
Return: S_OK = success, E_FAIL = unsuccessful
Analyzer Configuration
LoadConfig( BSTR cfg_filename )
Description: Load the specified configuration file. This is the quickest way to change all the analyzer settings.
Parameters: cfg_filename = filename of the configuration file. Full path or just filename if file located in /Config folder
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will look in the Config path as listed in the <File><Set Paths> dialog box.
SaveConfig( BSTR cfg_filename )
Description: Save the current settings to the specified configuration file
Parameters: cfg_filename = filename of the configuration file.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will store in the Config path as listed in the <File><Set Paths> dialog box.
SetMode( long mode )
Description: Set the current mode
Parameters: mode: 0 = Real Time, 1 = Recorder, 2 = Post Processing
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ChannelEnable( long channel )
Description: Enable the specified channel
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ChannelDisable( long channel )
Description: Disable the specified channel
Parameters: channel = 0 - 15
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
RecordEnable( long channel )
Description: Enable recording for the specified channel (device channel must also be enabled - use ChannelEnable())
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
RecordDisable( long channel )
Description: Disable recording for the specified channel
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSamplingRate( long rate )
Description: Set the sampling rate for the device
Parameters: rate = samples per second (applies to all channels)
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSamplingPrecision( long bits )
Description: Set the sampling precision for the device
Parameters: bits = bits per sample (applies to all channels)
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetFFTsize( long channel, long fft_size )
Description: Set the FFT size for the specified channel
Parameters: channel = 0 - 16, fft_size = 32 through 1048576 pts
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSmoothingWindow( long channel, long window )
Description: Set the Smoothing window for the specified channel
Parameters: channel = 0 - 16, window = values as shown below:
BARTLETT 0
BLACKMAN 1
EXPONENTIAL 2
FLATTOP 3
FORCE 4
HAMMING 5
HANNING 6
KAISER 7
PARZEN 8
TRIANGULAR 9
UNIFORM 10
GAUSSIAN 11
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetAverageMode( long channel, long mode )
Description: Set the Averaging Mode for the specified channel
Parameters: channel = 0 - 16, mode: 0 = Free Run, 1 = Sound Level Meter
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetAverageType( long channel, long type )
Description: Set the Averaging Type for the specified channel
Parameters: channel = 0 - 16, type: 0 = Exponential, 1 = Linear, 2 = Vector
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
EnablePSD( long channel )
Description: Enable Power Spectral Density scaling
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful
DisablePSD( long channel )
Description: Disable Power Spectral Density scaling
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful
SetAmplitudeScaleType( long channel, long scale_type )
Description: Set the amplitude axis scaling type for the specified channel
Parameters: channel = 0 - 16, scale_type: 0 = Linear, 1 = Logarithmic, 2 = Log Magnitude
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetFrequencyScaleType( long channel, long scale_type, long octave_number )
Description: Set the frequency axis scaling type for the specified channel
Parameters: channel = 0 - 16, scale_type: 0 = Linear, 1 = Logarithmic, 2 = Octave.
octave_number: 1,3,6,9,12,24,48,96 (ignored if scale_type not Octave)
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSpectrumWeighting( long channel, long weighting )
Description: Set the spectrum weighting for the specified channel
Parameters: channel = 0 - 16, weighting: 0 = Flat, 1 = A, 2 = B, 3 = C
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetTotalPowerWeighting( long channel, long weighting )
Description: Set the total power weighting for the specified channel
Parameters: channel = 0 - 16, weighting: 0 = Flat, 1 = A, 2 = B, 3 = C
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
TriggerEnable()
Description: Enable triggering
Return: S_OK = success, E_FAIL = unsuccessful
TriggerDisable()
Description: Disable triggering
Return: S_OK = success, E_FAIL = unsuccessful
SetTriggerThreshold( float threshold_volts )
Description: Set the trigger threshold
Parameters: the trigger threshold in volts. Must be between 0 and 10.0
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetAverageSize( long channel, long size)
Description: Set the average size for the specified channel
Parameters: channel = 0 - 16; size = average size 1 - 10000 (free run mode), 0 = Off, 1 = Fast, 2 = Medium, 3 = Slow, 4 = Forever (SLM mode)
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ResetAverage( long channel)
Description: Reset the running average for the specified channel
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetPeakHold( long channel_ext, long peak_hold_type )
Description: Set the peak hold type for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
peak_hold_type: 0 = Off, 1 = Fast, 2 = Medium, 3 = Slow, 4 = Forever
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ResetPeakHold( long channel_ext )
Description: Resets the peak hold values for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetOverlapPercentage( long channel, long overlap_percent )
Description: Sets the overlap percentage value for the specified channel
Parameters: channel = 0 - 16; overlap_percent = 1 - 99
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetCompensationFile( long channel, BSTR short_filename )
Description: Set the transducer compensation file for the specified channel
Parameters: channel = 0 - 16, short_filename: short filename (same as shown in the scaling dialog box). Use "None" to disable compensation.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetMarkerFreq( long channel_ext, long marker, float freqHz )
Description: Set the frequency for the specific channel and marker index
Parameters: channel_ext = 0 - 16 for main channels, 17 - 32 for composite channels;
marker = 1 - 8, freqHz = frequency in Hz
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ResetOverloadCount( )
Description: Reset the overload (clipping) count for all channels
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
DataLoggingEnable()
Description: Enable data logging
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
DataLoggingDisable()
Description: Disable data logging
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
LoadCalibrationFile( long channel, BSTR short_filename )
Description: Load the calibration file for the specified channel
Parameters: channel = 0 - 16; short_filename = the short filename of the calibration file (same as shown in the calibration dialog box). Use "Volts", "Millivolts" or "RPM" for the internally supported units.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
CalibrateToExternalSource( long channel, float source_level )
Description: Perform a calibration measurement on the specified channel
Parameters: channel = 0 - 16; source_level = value to calibrate to (SPL example: 94.0).
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Notes:
You must be using the calibration option to calibrate to an external source.
The measurement will continue until the following conditions are met:
1) The measured signal level is stable to within +/-0.1 millivolt. This is approximately +/-0.03 dB with typical mic sensitivities.
2) The measured signal level is within 12% of its original value. This is approximately +/-1 dB.
If both of these conditions are not satisfied within 60 seconds the measurement will stop and an E_FAIL error will occur.
These conditions will assure that settling has completed, the mic calibrator is turned on and the correct mic and channel are used.
SaveCalibrationFile( long channel, BSTR cal_filename )
Description: Save the calibration file for the specified channel
Parameters: channel = 0 - 16; cal_filename = filename of the calibration file.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will store in the Cal path as listed in the <File><Set Paths> dialog box.
SetChannelName( long channel, BSTR name )
Description: Set the channel name for the specified channel
Parameters: channel = 0 - 16; name = string to use as the channel name.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetRunControl( long mode, long fft_limit, float time_limit, float start_delay_time )
Description: Set the Run Control options
Parameters: mode: 0=Continuous, 1=Stop after FFT limit, 2=Stop after time limit
fft_limit: number of FFTs to process before stopping when mode = 1
time_limit: seconds to process before stopping when mode = 2
start_delay_time: seconds to delay before starting processor
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetMetadata( long channel, BSTR metadata )
Description: Set the metadata text to store in the current wafe file. Wave file must be open for this function to suceed.
Parameters: channel = 0 - 16; metadata - up to 2000 characters max of ascii text
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Plot and Window Commands
OpenPlot( long channel_ext, long plot_type )
Description: Opens a plot for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
plot_type: 1 = Time Series, 2 = Spectrum, 3 = Phase, 4 = Spectrogram, 5 = 3-D Surface
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ClosePlot( long channel_ext, long plot_type )
Description: Closes a plot for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
plot_type: 1 = Time Series, 2 = Spectrum, 3 = Phase, 4 = Spectrogram, 5 = 3-D Surface
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
MinimizeApplication( )
Description: Minimize the overall application window to an icon
Return: S_OK = success, E_FAIL = unsuccessful
MaximizeApplication( )
Description: Maximize the overall application window on the screen
Return: S_OK = success, E_FAIL = unsuccessful
RestoreApplication( )
Description: Restore the application to it's previous size
Return: S_OK = success, E_FAIL = unsuccessful
HideApplication( )
Description: Hide the overall application window and icon.
Return: S_OK = success, E_FAIL = unsuccessful
ShowApplication( )
Description: Show the overall application window and icon (restore from HideApplication())
Return: S_OK = success, E_FAIL = unsuccessful
ClearSpectrum( long channel_ext )
Description: Clears the spectral data for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ClearPeakHoldSpectrum( long channel_ext )
Description: Clears the peak hold spectral data for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSpectrumPlotFrequencySpan( long channel_ext, float startHz, float stopHz )
Description: Set the displayed frequency span for the spectrum plot for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
startHz = start frequency, stopHz = stop frequency
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSpectrumPlotTop( long channel_ext, float plot_top )
Description: Set the display amplitude plot top parameter for the spectrum plot for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels; plot_top = plot top value
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSpectrumPlotRange( long channel_ext, float plot_range )
Description: Set the display amplitude plot range parameter for the spectrum plot for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels; plot_range = plot range value
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetSpectrumPlotGraphType( long channel_ext, long graph_type )
Description: Set the spectrum plot graph type for the specified channel
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
graph_type: 0 = Line, 1= Bars, 2 = Stepped Bars
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetTimeSeriesPlotTimeSpan( long channel, float start_time, float stop_time )
Description: Set the time span to be displayed on the time series plot
Parameters: channel = 0 - 16, start_time, stop_time = time span to display
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
WritePlotToBitmapFile( long channel_ext, long plot_type, BSTR bmp_filename )
Description: Saves the plot image to a bitmap file
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
plot_type: 1 = Time Series, 2 = Spectrum, 3 = Phase, 4 = Spectrogram, 5 = 3-D Surface
bmp_filename = full filename and path to store bitmap
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Overlay Control
SetOverlay( long channel_ext, long overlay_index, int create_from_peak_hold, BSTR szLegend)
Description: Create an overlay from the current spectral data
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
overlay_index = 1 - 7
create_from_peak_hold = 1 to create the overlay from the peak hold values (peak hold must be enabled)
szLegend = legend to apply to overlay
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
ShowOverlay( long channel_ext, long overlay_index)
Description: Shows the specified overlay
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
overlay_index = 1 - 7
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
HideOverlay( long channel_ext, long overlay_index)
Description: Hides the specified overlay
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
overlay_index = 1 - 7
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SaveOverlay( long channel_ext, long overlay_index, BSTR ovl_filename)
Description: Save an overlay to a file
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
overlay_index = 1 - 7
ovl_filename = name of the overlay file.
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will store in the Overlay path as listed in the <File><Set Paths> dialog box.
LoadOverlay( long channel_ext, long overlay_index, BSTR ovl_filename)
Description: Load an overlay from a file
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
overlay_index = 1 - 7
ovl_filename = name of the overlay file to load
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will load it from the Overlay path as listed in the <File><Set Paths> dialog box.
File Management
FileOpen( long channel, BSTR wav_filename)
Description: Open a wave file on the specified channel.
Parameters: channel = 0 - 16; wav_filename =filename
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will look in the Wave path as listed in the <File><Set Paths> dialog box.
FileSave( long channel, BSTR wav_filename)
Description: Save the wave file on the specified channel.
Parameters: channel = 0 - 16; wav_filename = filename
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: If a short filename is used, it will store in the Wave path as listed in the <File><Set Paths> dialog box.
FileClose( long channel )
Description: Close the wave file on the specified channel
Parameters: channel = 0 - 16
Note: if the channel parameter is set to -1, all open wave files will be closed without saving
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
File Positioning
FileRewind( long channel )
Description: Go to the start of the wave file on the specified channel
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileForward( long channel )
Description: Go to the end of the wave file on the specified channel
Parameters: channel = 0 - 16
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileGoToTime( long channel, float seconds)
Description: Go to a specific time on the specified channel
Parameters: channel = 0 - 16; seconds = file position in seconds
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileGoToSample( long channel, unsigned long sample)
Description: Go to a sample position on the specified channel
Parameters: channel = 0 - 16; sample = file position in samples
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
File Post Processing
FilePlaySegmentTime( long channel, float start_seconds, float stop_seconds)
Description: Playback the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FilePlaySegmentSample( long channel, unsigned long start_sample, unsigned long stop_sample)
Description: Playback the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_sample = segment start sample position; stop_sample = segment stop sample position
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileFilterSegmentTime( long channel, float start_seconds, float stop_seconds)
Description: Filter the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileFilterSegmentSample( long channel, unsigned long start_sample, unsigned long stop_sample)
Description: Filter the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_sample = segment start sample position; stop_sample = segment stop sample position
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileProcessSegmentTime( long channel, float start_seconds, float stop_seconds)
Description: Computes the average spectral data for the specified time segment for the selected channel (same as right clicking on time series plot and choosing "Compute Average Spectrum")
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time.
Note: If the specified time segment is less than a full FFT size, zero padding will be applied
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileProcessSegmentSample( long channel, unsigned long start_sample, unsigned long stop_sample)
Description: Computes the average spectral data for the specified time segment for the selected channel (same as right clicking on time series plot and choosing "Compute Average Spectrum")
Parameters: channel = 0 - 16; start_sample = segment start sample position; stop_sample = segment stop sample position
Note: If the specified time segment is less than a full FFT size, zero padding will be applied
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileCutTime( long channel, float start_seconds, float stop_seconds)
Description: Cut the specified time segment for the selected channel and place it on the clipboard
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileCutSamples( long channel, long start_sample, long stop_sample)
Description: Cut the specified time segment for the selected channel and place it on the clipboard
Parameters: channel = 0 - 16; start_sample = segment start position; stop_sample = segment stop position
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileCopyTime( long channel, float start_seconds, float stop_seconds)
Description: Copy the specified time segment for the selected channel and place it on the clipboard
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileCopySamples( long channel, long start_sample, long stop_sample)
Description: Copy the specified time segment for the selected channel and place it on the clipboard
Parameters: channel = 0 - 16; start_sample = segment start position; stop_sample = segment stop position
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FilePasteTime( long channel, float paste_position_seconds)
Description: Paste the current clipboard contents (wave data) into the current file at the specified position
Parameters: channel = 0 - 16; paste_position_seconds = location to paste the data
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FilePasteSamples( long channel, long paste_position_sample)
Description: Paste the current clipboard contents (wave data) into the current file at the specified position
Parameters: channel = 0 - 16; paste_position_sample = location to paste the data
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileMuteTime( long channel, float start_seconds, float stop_seconds)
Description: Mute the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileMuteSamples( long channel, long start_sample, long stop_sample)
Description: Mute the specified time segment for the selected channel
Parameters: channel = 0 - 16; start_sample = segment start position; stop_sample = segment stop position
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileBuildSpectrogramPlot( long channel_ext, float start_seconds, float stop_seconds)
Description: Computes and displays the Spectrogram plot for the specified time segment for the selected channel (same as right clicking on time series plot and choosing "Compute and Display Spectrogram")
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
FileBuildSurfacePlot( long channel_ext, float start_seconds, float stop_seconds)
Description: Computes and displays the 3-D Surface plot for the specified time segment for the selected channel (same as right clicking on time series plot and choosing "Compute and Display 3-D Surface")
Parameters: channel_ext = 0 - 16 for main channels, 17 -32 for composite channels;
start_seconds = segment start time; stop_seconds = segment stop time
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid paramete
Signal Generation
OpenGenerator()
Description: Open the signal generator utility
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
CloseGenerator()
Description: Close the signal generator utility
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
RunGenerator()
Description: Start the signal generator
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
StopGenerator()
Description: Stop the signal generator
Parameters: none
Return: S_OK = success, E_FAIL = unsuccessful
SetGeneratorSignalType( long channel_sig, long signal_type )
Description: Set the signal type for the specified signal generator channel
Parameters: channel = 0 - 1; signal_type - as follows:
0 = White Noise
1 = Pink Noise
2 = Noise Burst
3 = 1 kHz Tone
4 = Multiple Tones
5 = Tone Burst
6 = IMD Tones
7 = Freq Sweep
8 = Level Sweep
9 = Sawtooth
10 = Triangular
11 = Pulse
12 = Squarewave
13 = User Defined wave file
14 = DTMF
16 = Digital Zero
16 = Frequency Step
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
SetGeneratorLevel( long channel_sig, float volts )
Description: Set the output level for the specified signal generator channel
Parameters: channel = 0 - 1; volts = rms voltage level
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: The output units will change to Volts when this command is used.
SetGeneratorFreq( long channel_sig, float freqHz )
Description: Set the signal type to Multiple tones and enable only a single tone at the specified frequency. The multitone level is set to 0 dBr (use SetGeneratorLeve() to set the output level)
Parameters: channel_sig = 0 - 1; freqHz = frequency in Hz
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: The signal type will change to Multiple Tones when this command is used.
SetGeneratorMultiTone( long channel_sig, long tone_idx, int enable, float freqHz, float levelDBr, float phaseDeg)
Description: Set the signal type to Multiple tones and set the parameters for a specific tone index.
Parameters: channel_sig = 0-1; tone_idx = 0-9, enable = 0 (off) or 1 (on), freqHz = frequency in Hz, levelDBr = relative level of tone in dBr (0.0 to -96), phase in degrees (-180 to +180)
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: The signal type will change to Multiple Tones when this command is used.
LoadGeneratorMultiToneFile( long channel_sig, BSTR toneFilename )
Description: Load a .tones file from disk - this allows you to change the set of tones
Parameters: channel_sig = 0 - 1; toneFilename = name of .tones file
Return: S_OK = success, E_FAIL = unsuccessful, E_INVALIDARG = invalid parameter
Note: The signal type will change to Multiple Tones when this command is used.
Digital Input and Output Lines
Many of the Data Translation modules have Digital Input and Output lines for controlling and
reading external equipment such as relays. These functions allow you to read and write the
state of these lines.
GetDigitalInputLineState( DWORD *state )
Description: Get the current state of the digital Input lines
Parameters: state = pointer to value to receive the current state of the digital input lines
Return: S_OK = success, E_FAIL = unsuccessful
SetDigitalOutputLineState( DWORD state )
Description: Set the current state of the digital Output lines
Parameters: state = value containing the new state to set the output lines
Return: S_OK = success, E_FAIL = unsuccessful